Products

1/3 hp TX Motor with 60” Square Drive Heavy Duty Shaft & Sheath, TXR Plastic Foot Pedal Speed Control, 115v

1/3 hp TXB Bench Mount Motor with 60” Square Drive Heavy Duty Shaft & Sheath and EMX Plastic Table Top Dial Speed Control, 115v

1/3 hp TXM Bench Mount Motor with 60” Square Drive Heavy Duty Shaft & Sheath and Built-in Dial Speed Control, 115v

1/3 hp TXM Bench Mount Motor with Standard Shaft & Sheath and Built-in Dial Speed Control, 115v

1/6 hp Bench Mount SR Motor w/ built-in control, H.30 Handpiece, 115v

1/6 hp SR Motor, SCT Metal Foot Pedal Speed Control, H.30 Handpiece, 115v

1/6 hp SRB Bench Mount Motor with Standard Shaft & Sheath and FCT-1 Plastic Foot Pedal Speed Control, 115v

Accessory Holder Arm, for 99 3/32” shank bits, 3 Tiers, Accy. bar measures 30cm long x 5cm wide x 5cm, high, for use on MAMH-13

Accessory Kit, Assorted Accessories for Jewelry, 3/32” Shanks

Accessory Tray Arm, tray measures 30cm long x 6cm wide x 3cm high, tray interior 27cm long x 5.7cm wide x 2.8cm deep, for use on MAMH-13

Angle Grinder AK69110 and H.30

Angle Grinder Attachment Only

Anvil Point Assortment Kit, 1 ea. HP10171, HP10172, HP10173, HP10175, HP10176, HP10179

Anvil Point, Ball Nose, 3/32” (2.3mm), 1/8-48 US Threaded for #15 Handpiece & HPMH-011 Micro Motor Hammer handpiece

Anvil Point, Bezel Rocker, 3/32” x 3/4” (2.3mm x 18.0mm), 1/8-48 US Threaded for #15 Handpiece & HPMH-011 Micro Motor Hammer handpiece

Anvil Point, Cylinder, 7/32” (6.0mm), 1/8-48 US Threaded for #15 Handpiece & HPMH-011 Micro Motor Hammer handpiece

Anvil Point, Fine Point, .015” (0.4mm), 1/8-48 US Threaded for #15 Handpiece & HPMH-011 Micro Motor Hammer handpiece

Anvil Point, Flat Top Taper, 3/32” (2.3mm),Threaded for #15 Handpiece

Anvil Point, Rectangle, 3/32” x 3/16” (2.3mm x 4.8mm), 1/8-48 US Threaded for #15 Handpiece & HPMH-011 Micro Motor Hammer handpiece

Anvil Point, Square Tip, 3/32” (2.3mm), 1/8-48 US Threaded for #15 Handpiece & HPMH-011 Micro Motor Hammer handpiece

Base & Yoke Assembly, TX, TXH, S, & SR Series Motors

Base Mounting Assembly for MAMH-13 Motor Hanger

Base Mounting Assembly for Motor Hangers MH-2

Bench Clamp Assembly for motor hangers MH-1 & HH-30

Brushless Micromotor Kit w/ H.MH-150 w/ 1/8” Collet, HPMH-011 Hammer Handpiece, Dual Port Control Box HP4-817, Varible Speed Control Foot Pedal HP7-7060 & Handpiece Cradle HP4-933, 115V

Brushless Micromotor Kit w/ Rotary Handpiece MH-150 w/ 1/8”

Carbide Stylus, Threaded for #15 Handpiece

Chuck Key, No Molded Handle, for #30, #30H, #30SJ & #25C Handpieces

Chuck Key, with Molded Handle, for #30, #30H, #30SJ & #25C Handpieces

Collet Adaptor, Angle Grinder, w/1/8” & 3/32” collets and wrench set

Collet Adaptor, Reducing 1/8” to 1/16”

Collet Adaptor, Reducing 1/8” to 3/32”